How to Make Gopro Mounts Sticky Again
I was a bit hesitant before buying the GoPro adhesive camera mountain considering I was unsure how long information technology would concluding or if it would actually work. I did some research and also reached out to the 3M product support team for some answers. I discovered in that location are a few factors that impact your agglutinative mount lifespan.
How long tin can an adhesive GoPro mount maintain its stickiness before losing effectiveness and weakening? This depends on a few unlike factors:
- Installation of the tape
- Surface preparation
- Surface contour
- Using the correct tape based on substrates
- Bonding surface-expanse-to-weight
- Cure time
- Temperature
- Storage location
- Sun exposure
While information technology might be easy to blame the integrity of the adhesive mounting record, failure can be due to one of these ix common factors. Let's take a deeper look into these to aid you become aware of how each can affect the overall force of the bond.
(ane) Installation of the adhesive mountain to your handboard
Installing a GoPro adhesive mount to the deck of your bodysurfing handboard is a relatively easy task. However, it is important that y'all exercise it correctly if you lot want information technology to remain attached to your board. The liner needs to exist removed first and the mount needs to be firmly pushed information technology into the lath so the entire surface area of the tape is in contact.
(2) Surface training
Surface preparation is very disquisitional. In guild for an adhesive GoPro mount to bond successfully to your bodysurfing handboard, y'all need to make certain the surface is super clean.
Whatever traces of dirt, grime, or dust volition impair the bonding of the agglutinative to the surface. Therefore yous need to wipe the surface area with rubbing alcohol and then dry it before placing the adhesive mount on your lath.
(3) Surface contour & shape
The surface profile of your bodysurfing handboard will bear upon the effectiveness of an adhesive camera mount. A flat, level surface is needed for optimal bonding.
If part of the surface area of the mount tape is not in contact with the board, the integrity of the adhesive becomes compromised thus rendering information technology ineffective.
Handboards with an farthermost concave blueprint, like the Slyde Bula, do not permit for the entire adhesive to make contact with the surface of the deck. The Slyde Wedge, on the other hand, is a more favorable surface for agglutinative surf mounts. I wrote a post that discusses which
(4) Using the correct record based on substrates
Information technology is important to note that non all VHB tapes bond equally to all types of substrates. An issue many people don't recollect virtually is the motility of materials between surfaces.
Adhesive tape that is left on a surface for a long time can trigger a migration of materials from the substrate to the tape. Therefore y'all demand to employ the tape that is designed for the specific blazon of surface you are installing information technology on.
Below is a table of substrates and the corresponding VHB record serial that should be used for bonding. This volition be a helpful reference if you lot need to replace the adhesive on your camera mountain.
| Material (Substrate) | VHB Record Series |
| Polyethylene | 5900 |
| Polypropylene | 5900 |
| Powder Coated S | 5900 |
| Vinyl | 4926, 4942, 4956 |
| Flexible PVC | 4926, 4942, 4956 |
| Acrylic | 4900 |
| ABS | 4900 |
| Fiberglass | 4900 |
| Polycarbonate | 4900 |
(5) Bonding surface-area-to-weight ratio
Some other factor that can impact the effectiveness of an adhesive mount is the weight of the object and the amount of area the adhesive touches. The sticky surface needs to cover a big enough area in club to support the weight of the object attached to it. Therefore, the larger the bonding surface the stronger the hold.
(6) Cure fourth dimension
How long should you wait before using an agglutinative photographic camera mount after installation? It is not recommended to use your agglutinative mount immediately after installation. I emailed 3M well-nigh this and they recommended a cure time of roughly 72 hours to let the adhesive mount to reach its maximum forcefulness.
(7) Temperature
Temperature can bear upon the strength of the overall stickiness. Farthermost cold can create poor bonding between the surface and tape. Very high and temperatures can crusade the adhesive material to melt.
Furthermore, farthermost, consequent temperatures tin cause deterioration. If you lot are worried near the climate affecting the forcefulness of your adhesive mount then you should purchase temperature-sensitive tape.
(8) Storage location
Improperly storing your agglutinative mounts can compromise the integrity. Therefore your agglutinative mount should not be stored in any clammy or dirty places. Also, avoid storing the record in extremely hot or cold environments.
You lot can run across in the image in a higher place that I store mine in a plastic bag with other mounting accessories. I place it in one of the drawers in my nightstand. This keeps it dry and
(9) Sun exposure
Exposing record to UV rays for a long time tin alter the textile properties in a negative way. The adhesive tin can weaken and dry out from too much sunday exposure ultimately shrinking the lifespan and causing it to fail.
What type of tape does an agglutinative GoPro mount utilise?
The blazon of agglutinative used for GoPro mounts is 3M VHB record. GoPro really sells them on their website just y'all can besides find them for inexpensive on Amazon similar this surf mounting kit. You simply skin dorsum the liner in lodge to apply.
How strong is a GoPro adhesive mountain?
The 3M VHB adhesive mount is a very strong, permanent bail. It can withstand impact of big waves and high wind.
Does water event stickiness of GoPro mountain?
I asked 3m this question and the product support specialist explained that the adhesive VHB mount is water-resistant. Therefore, water should non compromise the strength and stickiness of an agglutinative GoPro mount.
Surfers and handboarders alike use this type of mount to moving-picture show their epic wave riding sessions. I use it to film mine likewise and information technology remains stuck to the lath.
Can you lot reuse GoPro adhesive mounts?
This was another question that I asked the production experts at 3M. They explained that you cannot "reuse" the VHB adhesive. Instead, y'all will accept to replace the adhesive entirely. Also, if you visit the GoPro website, they explain that information technology cannot exist reused as well and volition take to purchase new agglutinative tape for your mount.
Do GoPro agglutinative mounts come off?
Fifty-fifty though these types of mounts form a very strong bail, they practise come up off. In club to remove an agglutinative surf
Related Questions:
Can the plastic mount break?
The plastic role of the mount is more likely to pause before the actual adhesive loosens. Since plastic mounts tin break, I highly recommend using mountain tethers to proceed your camera secure.
How to foreclose losing your GoPro when using an adhesive mountain?
Sometimes adhesive mounts can fail so it is important to tether your camera to a tether anchor so yous do not lose it. Tether anchors are pocket-sized mounts you tin install to your board next to the actual adhesive mount.
You could also spike a thin cord on ane end of the photographic camera and tie the other to your hand strap. This way if the adhesive mount fails or clip breaks your photographic camera will remain connected to the hand strap.
Lastly, print your proper noun, telephone number or email on a piece of paper and stick it somewhere inside your camera instance. This manner if you do lose it and somehow information technology resurfaces, the person that finds it can notify you (if they don't keep it themselves).
reyesmamrainy1941.blogspot.com
Source: https://bodysurfinghandboard.com/adhesive-mount-lifespan/
Post a Comment for "How to Make Gopro Mounts Sticky Again"